A “jack kit” can be a replacement seal kit
Page 45 distinguishes the older and newer piston rod assemblies by their packings. The contrast in the figure is a parts-identification clue, not a list of what arrives in a package advertised as a trench jack. [4]
On page 45 of Kundel’s TREN-SHORE manual, older piston rod assemblies have three thinner piston packings; newer assemblies have one thicker packing. Both appear under “jack kits.” Ordering by that heading alone does not even identify the packing for the assembly in hand, much less establish that a package contains a complete shore. [4]
The manual is for the TREN-SHORE aluminum hydraulic trench shoring system, effective November 2025. The example here is limited to the cover and replacement-parts pages 44–47: pump kits, jack kits, rail kits, and hose and finger-guard kits. It is not a bill of materials or an installation procedure for any particular delivery. [4]
Identify the shore, not just a cylinder
Aluminum hydraulic shoring uses hydraulic cylinders (crossbraces) with vertical uprights or horizontal wales to support excavation sides. A shield, by contrast, withstands cave-in forces to protect employees inside it. A part described as a jack does not establish which complete system, if any, the seller is offering. [1]
The rail section shows how specific a family entry can be. It states that rails are supplied as a set and include pins, keepers, handles and finger guards, and it lists standard rails separately from pre-drilled versions. The hose and finger-guard section adds rail handle sets, finger guards offered in more than one set size, and cylinder hose items. None of that describes a complete trench shoring system ready to install. [4]
The words “trench jack” also appear in a hose description on page 47. That wording does not establish equivalence with a separately marketed TrenchJack system. Ask the supplier for the maker, exact model, build or revision, complete assembly list and matching data before treating the package as a shore. [4]
Read the parts record alongside the design record
A replacement parts list answers a narrow question about the components it names. It is not a bill of materials for the complete shore or design data for the intended configuration. [4] [3]
For aluminum hydraulic shoring, §1926.652(c)(1) points to the manufacturer’s tabulated-data option and allows Appendix D where that data cannot be used. On the manufacturer route, follow all specifications, recommendations and limitations; any deviation requires the manufacturer’s specific written approval. Keep the written data and any approval at the jobsite during construction of the system. [3]
The other routes carry their own records. Designs from other tabulated data must be written and identify the parameters that affect selection, the limits of use, explanatory information, and the registered professional engineer who approved the data. Where none of the listed options is used, a registered professional engineer's design for the trench is required, including a plan of sizes, types and configurations and the engineer's identity. [3]
Check condition independently of the parts match
Damaged equipment follows a defined sequence rather than a judgment call at the truck. A competent person examines it and evaluates suitability for continued use; if that person cannot assure it can support the intended loads or is otherwise suitable for safe use, it is removed from service, and a registered professional engineer must evaluate and approve it before it returns. [3]
A delivery record is not a field inspection. Where employee exposure can reasonably be anticipated, the competent person inspects the excavation, adjacent areas and protective systems before work daily, as needed during the shift and after rainstorms or other hazard-increasing events. Remove exposed employees if hazardous conditions are found, until the necessary precautions have been taken. [2]
What a replacement kit proves
A package that matches a replacement parts list establishes what the kit contains. It does not establish that the remaining rails, cylinders and connections are present, suitable or covered by the design for a particular excavation. [3] [4]
Sources
- 29 CFR 1926.650: Scope, application, and definitions applicable to this subpartOccupational Safety and Health Administration
- 29 CFR 1926.651: Specific excavation requirementsOccupational Safety and Health Administration
- 29 CFR 1926.652: Requirements for protective systemsOccupational Safety and Health Administration
- Tren-Shore Aluminum Hydraulic Trench Shoring System manual (effective November 2025)Kundel Industries